ASTM D3171 PDF

Intertek tests composite materials constituent content, using ASTM D Content analysis for composite materials ASTM D scope: The test method ASTM. Intertek tests composite materials constituent content, using ASTM D Content analysis for composite materials ASTM D scope: The test method. To extend the burn off test protocol in ASTM D to the determination of The current ASTM test method incorporates resin burn off as a way to determine.

Author: Nimi Tejin
Country: Kosovo
Language: English (Spanish)
Genre: Literature
Published (Last): 13 July 2007
Pages: 170
PDF File Size: 16.42 Mb
ePub File Size: 7.19 Mb
ISBN: 804-2-85671-937-8
Downloads: 76681
Price: Free* [*Free Regsitration Required]
Uploader: Dojin

Validating the specifications, value and x3171 of your raw materials, products and assets. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The test is typically intended for two component materials.

ASTM D – 11 Standard Test Methods for Constituent Content of Composite Materials

Need help or have a question? The resulting solution is then filtered and the amount of remaining fiber is determined. Active view current version of standard.

Method I removes the matrix by digestion or ignition. Knowledge of the void volume of a composite material is desirable as an indication of the quality of a composite. Inspection Validating the specifications, value and safety of your raw materials, products and assets. Test Method I physically removes the matrix by digestion or ignition or carbonization by one of eight procedures, leaving the reinforcement essentially unaffected and thus allowing calculation of reinforcement or matrix content by weight or volume as well as percent void volume.

Testing Evaluating how your products and services meet awtm exceed quality, safety, sustainability and performance standards.

Test Method I physically removes the matrix by digestion or ignition by one of seven procedures, leaving the reinforcement essentially unaffected and thus allowing calculation of reinforcement or matrix content by weight or volume as well as percent void volume. Formally confirming that your products asstm services meet all trusted external and internal standards.

The presence of voids is not measured. The specimens are dried and cooled. Assurance Testing Inspection Certification.

Test Method II, d171 only to laminate materials of known fiber areal weight, calculates reinforcement or matrix content by weight or volumeand the cured ply thickness, based on the measured thickness of the laminate. However, special provisions can be made to extend these test methods to filled material systems with more than two constituents, though not all test results can be determined in every asgm.

  LIBRETTO PONTEGGIO CARPEDIL PDF

Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world.

See Section 9 for additional information. Eq 9 and 10 assume zero void content to perform the calculation. Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.

Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries. Also, knowledge of the constituent content is required for evaluation of the quality of a fabricated material and the processes used during fabrication.

No other units of measurement are included in this standard. Through our network of over 43, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world.

Procedures A through F are based on chemical removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace. Send ast a request Need help or have a question? Method II is only for laminates and uses calculations based on thickness.

Higher void volumes usually mean lower fatigue resistance, greater susceptibility to moisture penetration and weathering, and increased variation or scatter in strength properties. A procedure for d31711 of the results for minor changes in the reinforcement is included.

Link to Active This link will always route to the current Active version of the standard. See Section 9 astmm additional information. The suggested applications are discussed in Section 4, as well as at the start of each procedure. The suggested applications are discussed in Section 4as well as at the start of each procedure.

Test Method II is not applicable to the measurement of void volume. For method I, three specimens are machined from customer supplied product.

Content Analysis for Composite Materials by ASTM D

The test method ASTM D provides two procedures for determining xstm content of composite materials. Procedures A through F are based on chemical removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace.

  A.W.PINK THE ATTRIBUTES OF GOD PDF

Work Item s – proposed revisions of this standard. The presence of adtm is not measured. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to asttm. Send us a request Wilton UK: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Assurance Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes.

d3117 A procedure for correction of the results for minor changes in the reinforcement is included. However, special provisions can be made to extend these test methods to filled material systems with more than two constituents, though not all test results can astmm determined in every case.

Test Method II, applicable only to laminate materials of known fiber areal weight, calculates reinforcement or matrix content by weight or volumeand the cured ply thickness, based on the measured thickness of the laminate.

Historical Version s – view previous versions of standard. No other units of measurement are included in this standard. Auditing Consulting Sourcing Training.

Content Analysis for Composite Materials by ASTM D3171

It zstm the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Eq 15 and 16 assume zero void content to perform the calculation.

R3171 Formally confirming that your products and services meet all trusted external and internal standards. From the specimen density, constituent densities, and the fiber content, the reinforcement content, matrix content, and void content can then be determined. Procedure H carbonizes the matrix in a furnace.