EN ISO 6507-1 PDF

hardness test —. Part 1: Test method. Matériaux métalliques — Essai de dureté Vickers —. Partie 1: Méthode d’essai. STANDARD. ISO. Fourth edition. Purchase your copy of BS EN ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. I.S. EN ISO is the adopted Irish version of the European . The text of ISO has been approved by CEN as EN ISO.

Author: Zumi Mezit
Country: Fiji
Language: English (Spanish)
Genre: Environment
Published (Last): 6 March 2017
Pages: 315
PDF File Size: 16.91 Mb
ePub File Size: 1.81 Mb
ISBN: 456-4-35319-255-9
Downloads: 98929
Price: Free* [*Free Regsitration Required]
Uploader: Dougul

Isl guideline for the determination is given in Annex D. It is strongly recommended that this procedure be applied for a maximum of one year after the successful passing of a direct verification.

NBN EN ISO 6507-1

Your reading intentions are private to you and will not be shown to other users. The error b step 10 can be expected to be a iwo effect.

If not, an indirect verification should be performed. The chain starts at the international level using international definitions of the various hardness scales to carry out international intercomparisons. This is the base of M2.

Adobe is a trademark of Adobe Systems Incorporated. In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. Setting up reading intentions help you organise your course reading. The measured dimension should agree with the certified value to fn the maximum permissible error given in Table 5 of ISO The correction factors are tabulated in terms of the ratio of the mean diagonal d of the indentation to the diameter D of the cylinder.

NBN EN ISO | NBN

Supersedes BS EN There is no correction of the hardness values with respect to the error. Figure 1 — Principle of the test 6570-1 Vickers hardness is proportional to the izo obtained by dividing the test force by the sloping area of the indentation, which is assumed to be a fn pyramid with a square base, and having at the vertex the same angle as the indenter. For dated references, only the edition cited applies.

  CULTURE AND AUTHENTICITY CHARLES LINDHOLM PDF

Ihre Klassifizierung und Auswirkung auf die Messwerte. Document Status Indicators The Green document status 65007-1 indicates that the document is: The Amber document status indicator indicates that some caution is needed when using this document – it is either: The procedure for the determination of Ucorr is explained in Table D. This item appears on List: Verlag Berliner Union Stuttgart,pp The specification for the product may indicate limits for the differences between the lengths of the two diagonals.

It makes it easy to scan through your lists and keep track of progress. Every care has been taken to ensure that the file is suitable for use by ISO member bodies.

NOTE 1 A strict comparison of hardness values is only possible at identical test forces. Draft International Standards adopted by the technical committees are circulated to the member 6507–1 for voting. The time from the initial application of the force until the full test force is reached shall not be less than 2 s nor greater than 8 s.

The 6507-11 mean of the two readings shall be taken for the calculation of the Vickers hardness. Care should be taken, if standard uncertainties of type A and B are summarised, that the contributions are not counted twice see Clause 4 of GUM: There is no general process of accurately converting Vickers hardness into other scales of hardness or into tensile strength.

To set a reading intention, click through to any list item, and look for the panel on the left hand side:. It should be noted that for anisotropic materials, for example those which have been heavily cold-worked, there will be a difference between the lengths of the two diagonals of the indentation.

For automated measuring systems this standard should be applied accordingly. Want access to British Standards? Such conversions, therefore, should be avoided, unless a reliable basis for conversion can be obtained by comparison tests.

Ej accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.

  GENERAC RTSX100A3 PDF

In GUM, it is recommended to use a correction to compensate for such systematic effects. How do I set a reading intention To ido a reading intention, click through to any list item, and look for the panel on the left hand side: Specifies the Vickers hardness test method, for the three different ranges of test force for metallic materials.

Attention is drawn to 65077-1 possibility that some of the elements of this document may be the subject of patent rights. Independent of the type of sources, for hardness there are two possibilities for the determination of the uncertainty. The finish of the surface shall permit accurate determination of the diagonal length of the indentation. The corresponding effect on the termination of the formation of an indentation can make alterations in the hardness value.

As a reference, an EA guideline [7] is available. Here’s an example of what they look like:. The duration of the test force shall be 10 s to 15 s, except for tests on materials whose time-dependent properties would make this an unsuitable range.

Test method fn Scope This part of ISO specifies the Vickers rn test method, for the three different ranges of test force for metallic materials see Table 1. These performance uncertainties reflect the combined effect to all the separate uncertainties indirect verification. This is particularly true for low-force Vickers hardness 65077-1 and Ixo microhardness tests, where the principal limitation will arise in the measurement of the diagonals of the indentation.

In this case, an estimate of type A standard uncertainty may be obtained from the statistical analysis of repeated indentations into the test piece. Your reading intentions are also stored in your profile for future reference. Introduction to Materials and Materials Forming Next: